Try our Frames Site, if your browser supports it - it loads much faster.

 

Accessory Connector Details

The 16-pin accessory connector pin functions are as follows:

Pin Name Type 4-Channel 128- Channel
1 SPKR- Analogue Output y y
2 Ext Mic Audio Analogue Input y y
3 GP1 Digital Input y y
4 GP2 Digital Output   y
5 Flat Tx Audio Analogue Input   y
6 BUS+ Digital i/o y y
7 GND GND y y
8 GP3 Digital i/o   y
9 GP4 Digital ip capture   y
10 Ignition Sense Digital Input y y
11 Rx Audio Analogue Output   y
12 GP5 Digital i/o   y
13** SW B+/GND Analogue output   y
14 GP6 Digital i/o   y
15 RSSI Analogue Output y y
16 SPKR+ Analogue Output y y

 

** Factory default SWB+.

Pin 1. - Speaker - audio

Speaker - and Speaker + (Pin 16) are used to connect an external speaker. The audio PA is a bridge amplifier with a minimum load resistance of 3.2 ohms. The internal speaker can be disabled by removing the control head. Disconnect the internal speaker and assemble the control head back to the radio.

Pin 2. - Microphone audio

This microphone signal input is common with the microphone signal input on the microphone connector and is connected to the rtiicrophone path input of the AFIC. The nominal input level is 80mV for 60% deviation. The DC impedance is 1100 ohms and the AC impedance is 1000 ohms Note: Only one microphone should be connected at any one time.

Pin 3. - General Purpose 1 (GP 1)

This is a digital input only. The RSS details which functions may be assigned to this pin by the codeplug. The primary use for this pin will be external PTT. (See Note 1).

Pin 4. - General purpose 2 (GP2)

This is a digital output only The RSS details which functions may be assigned to this pin by the codeplug. The primary use for this pin is as external alarm output (See Note 3).

Pin 5. - Flat TX audio

This input is for injecting signals into the transmit path that should not be filtered, e.g. the output of a modem. The nominal input level is l5OmVRMS for 60% deviation. The impedance is greater than 25kohms.

Pin 6. - BUS+

This connects to the radio's SCI serial bus which is used for programming and tuning the radio. The line is also available at the microphone connector Pin 7.

Pin 7. - Ground

Used as ground for both analogue and digital signals.

Pin B. - General purpose 3 (GP3)

This is a digital input/output and is also available on the internal option connector (JOl 03:7). The RSS details which functions may be assigned to this pin by the codeplug. (See Notes 1 and 2).

Pin 9. - General purpose 4 (GP4)

This is a digital input only. It is also available on the internal option connector (JO102:7) and is used in input capture mode when a serial type option board is fitted. The RSS details which functions may be assigned to this pin by the codeplug. (See Note 1).

Pin 10.- ignition sense

Connecting this line to the ignition line of the vehicle will automatically turn the radio on when the ignition of the vehicle is turned on. When ignition is connected, the radio cannot be turned off as long as the ignition is active. When this line is at OV or not connected, power on/off is under manual control. Resistor R0423, 4.7ki2, which is not fifted as standard will cause the radio to be permanently on whenever 12V is connected to the main power connector.

Pin I I.- RX Audio Discriminator/Filtered (Analogue output)

The signal routed to this pin is controlled by AFIC. There are two possible outputs; continuous discriminator audio or continuous filtered RX audio output of AFIC. The output mode can be selected by the RSS, however, this mode may be overridden during certain tuning operations. For discriminator audio, the nominal ouput level is 330mVRMS for 60% deviation. The impedance is 600ohms. For filtered audio, the nominal ouput level is 600mV for 60% deviation. The impedance is 600ohms.

Pin 12.- General purpose 5 (GP5)

This is a digital input/output and is also available on the internal option connector (JOl 03:8). The RSS details which functions may be assigned to this pin by the codeplug. (See Notes 1 and 2).

Pin 13.- Switched B+ / Analogue Ground

The output of this pin may be configured by a solder link within the radio. Switched B+ is the default. The current limiting resistor (RO455) default is O ohm, therefore extreme care must be taken to avoid short circuiting this output to ground, which will damage the radio.

CAUTION:The maximum continuous current allowed is 3OOmA. A suitable external fuse must be installed into the lead to pin 13 to avoid damage to the radio.

Pin 14.- General purpose 6 (GP6)

This is a digital input output and is also available on the internal option connector (J0102:3). The RSS details which functions may be assigned to this pin by the codeplug. (See Notes 1 and 2).

Pin 15.- RSSI

Received Signal Strength Indication, buffered analogue voltage.

Pin 16.- Speaker+ audio

Positive output of radio's audio PA (see Pin 1).

Note 1: Digital Input

4.7 k Internal Pull Up Resistor to +5V

Maximum Input Voltage accepted as Low = 0.6V Minimum Input Voltage accepted as High = 3.0V

Note 2: Digital Output

4.7k Internal Pull Up Resistor to +5V

Maximum Current when Output Low = 10mA Maximum Voltage when Output Low = 0.5V @ 110mA

Note 3: High Current Digital Output

4.7k Internal Pull Up Resistor to B+

Maximum Current when Output Low = 200mA Maximum Voltage when Output Low = 1.7V @200mA

 

Send mail to CompanyWebmaster with questions or comments about this web site.
Last modified: February 09, 2006